Hyundai Vehicle Models Veloster 2011-2018 Torque Specifications
Hyundai Vehicle Models Veloster 2011-2018

Hyundai Vehicle Models Veloster 2011-2018 Torque Specifications

Complete Hyundai Vehicle Models Veloster 2011-2018 torque specifications guide. Includes factory-specified torque values, torque sequences, and technical specifications for all components including body, brakes, drivetrain, electrical, emissions sensors, fuel, exhaust, HVAC, and suspension. Essential information for proper assembly and maintenance.

Updated

Important Information

Safety guidelines and reference information for proper torque application

Quick Reference Guide
ft-lbs → Nm
× 1.356
ft-lbs → kg-m
× 0.138
Nm → ft-lbs
× 0.738
in-lbs → ft-lbs
× 0.083

Common Torque Patterns

Star Pattern

Used for wheels and other circular bolt patterns

Star Pattern torque pattern diagram showing proper bolt tightening sequence
Cross Pattern

Used for gaskets and cover plates

Cross Pattern torque pattern diagram showing proper bolt tightening sequence
Sequential Pattern

Used for head bolts and other critical components

Sequential Pattern torque pattern diagram showing proper bolt tightening sequence

Common Mistakes to Avoid

Over-tightening

Exceeding the specified torque value can stretch or break fasteners, damage threads, or crack components.

Prevention:

Always use a calibrated torque wrench and follow specifications exactly.

Incorrect Torque Sequence

Tightening bolts in the wrong order can cause uneven pressure distribution and potential leaks or damage.

Prevention:

Follow the manufacturer's specified torque sequence pattern.

Dirty Threads

Dirt, rust, or old thread locker can affect torque readings and proper fastener tension.

Prevention:

Clean and inspect all threads before assembly. Use new thread locker if specified.

Reusing TTY Bolts

Torque-to-yield bolts are designed to stretch and must not be reused.

Prevention:

Always replace TTY bolts with new ones. They are single-use only.

Dry vs. Lubricated

Not accounting for whether torque specs are for dry or lubricated fasteners can lead to incorrect tension.

Prevention:

Check if specs are for dry or lubricated threads. Use specified lubricant when required.

Recommended Tools

Torque Wrench (1/4" Drive)

Range: 2-25 ft-lbs
Small fasteners, delicate components

Torque Wrench (3/8" Drive)

Range: 10-100 ft-lbs
Most common automotive fasteners

Torque Wrench (1/2" Drive)

Range: 30-250 ft-lbs
Large fasteners, wheels

Angle Gauge

Torque-to-yield (TTY) bolts

Torque Wrench Care

  • Calibrate annually or after 5,000 clicks
  • Store at lowest setting
  • Keep clean and lubricated

Search Specifications

Search by component name, bolt size, or description

Torque Calculator

Convert between different torque units

1.6l Engine

Torque specifications for 1.6L Engine

Cylinder Head

1

Cylinder Head Bolts

M10 x 1.25
Torque Specification
1. 18 ft-lbs (24 N·m) 2. 23 ft-lbs (31 N·m)
Important Notes
Follow the manufacturer's torque sequence to ensure even clamping force.
2

Valve Cover Bolts

M6 x 1.0
Torque Specification
6 ft-lbs (8 N·m)
Important Notes
Ensure the valve cover gasket is properly seated before tightening.

Crankshaft And Bearings

1

Main Bearing Bolts

M10 x 1.25
Torque Specification
59 ft-lbs (80 N·m)
Important Notes
Follow the manufacturer's torque sequence to ensure even clamping force.
2

Connecting Rod Nuts

M8 x 1.0
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Ensure the connecting rod bearings are properly seated before tightening.

Timing System

1

Camshaft Sprocket Bolt

M12 x 1.25
Torque Specification
67 ft-lbs (90 N·m)
Important Notes
Ensure the timing marks are aligned before tightening.
2

Timing Belt Tensioner Bolt

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure the tensioner is properly aligned before tightening.

Intake And Exhaust

1

Intake Manifold Bolts

M8 x 1.25
Torque Specification
16 ft-lbs (22 N·m)
Important Notes
Follow the manufacturer's torque sequence to ensure even clamping force.
2

Exhaust Manifold Bolts

M10 x 1.25
Torque Specification
33 ft-lbs (45 N·m)
Important Notes
Ensure the exhaust manifold gasket is properly seated before tightening.

Lubrication System

1

Oil Pan Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (9 N·m)
Important Notes
Ensure the oil pan gasket is properly seated before tightening.
2

Oil Drain Plug

M14 x 1.5
Torque Specification
33 ft-lbs (45 N·m)
Important Notes
Replace the crush washer to ensure a proper seal.

1.6l Turbo Engine

Torque specifications for 1.6L-TURBO Engine

Cylinder Head

1

Cylinder Head Bolts

M10 x 1.25
Torque Specification
1. 18 ft-lbs (24 N·m) 2. 23 ft-lbs (31 N·m)
Important Notes
Follow the manufacturer's specified torque sequence to avoid warping the cylinder head.

Crankshaft And Bearings

1

Main Bearing Bolts

M12 x 1.5
Torque Specification
58 ft-lbs (79 N·m)
Important Notes
Ensure the crankshaft is properly seated before tightening.
2

Connecting Rod Nuts

M8 x 1.0
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Ensure proper alignment of the connecting rod caps.

Flywheel

1

Flywheel Bolts

M10 x 1.25
Torque Specification
65 ft-lbs (88 N·m)
Important Notes
Use thread locker on the bolts to prevent loosening.

Oil System

1

Oil Pan Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (9 N·m)
Important Notes
Ensure the oil pan gasket is properly seated before tightening.
2

Oil Drain Plug

M14 x 1.5
Torque Specification
32 ft-lbs (43 N·m)
Important Notes
Replace the crush washer to ensure a proper seal.

Turbocharger

1

Turbocharger Mounting Bolts

M8 x 1.25
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Estimated value based on similar components.
2

Turbocharger Oil Feed Line Bolt

M6 x 1.0
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Estimated value based on similar components.

A6f Transmission

Torque specifications for A6f Transmission

Transmission Mounting

1

Transmission Mounting Bolts

M14 x 1.5
Torque Specification
72.5 ft-lbs (98.5 N·m)
Important Notes
Estimated value, consult manufacturer's documentation for exact specification.

Transmission Oil Pan

1

Transmission Oil Pan Bolts

M10 x 1.25
Torque Specification
72.5 ft-lbs (8.5 N·m)
Important Notes
Estimated value, consult manufacturer's documentation for exact specification.

Transmission Drain and Fill

1

Transmission Drain and Fill Plugs

M12 x 1.25
Torque Specification
32.5 ft-lbs (44 N·m)
Important Notes
Estimated value, consult manufacturer's documentation for exact specification.

Transmission Case

1

Transmission Case Bolts

M13 x 1.25
Torque Specification
40 ft-lbs (54 N·m)
Important Notes
Estimated value, consult manufacturer's documentation for exact specification.

Front Cover

1

Front Cover Bolts

M12 x 1.25
Torque Specification
30 ft-lbs (40 N·m)
Important Notes
Estimated value, consult manufacturer's documentation for exact specification.

Rear Cover

1

Rear Cover Bolts

M12 x 1.25
Torque Specification
30 ft-lbs (40 N·m)
Important Notes
Estimated value, consult manufacturer's documentation for exact specification.

Torque Converter

1

Torque Converter Bolts

M14 x 1.5
Torque Specification
45 ft-lbs (61 N·m)
Important Notes
Estimated value, consult manufacturer's documentation for exact specification.

Body

Torque specifications for Body

Suspension System

1

Strut/Shock Absorber Mounting Bolts

M14 x 1.5
Torque Specification
41 ft-lbs (55 N·m)
Important Notes
Secure the strut or shock absorber to the vehicle's body.
2

Control Arm Bolts

M16 x 2.0
Torque Specification
65 ft-lbs (88 N·m)
Important Notes
Attach the control arms to the vehicle's body, maintaining proper suspension geometry and stability.

Steering System

1

Steering Gear/Rack Bolts

M14 x 1.5
Torque Specification
65 ft-lbs (88 N·m)
Important Notes
Secure the steering gear or rack to the vehicle's body.

Body Mounts

1

Front Bumper Mounting Bolts (Estimated)

M10 x 1.5
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
Estimated torque value based on industry standards. Consult the vehicle's manufacturer or a trusted repair manual for specific guidance.
2

Rear Bumper Mounting Bolts (Estimated)

M10 x 1.5
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
Estimated torque value based on industry standards. Consult the vehicle's manufacturer or a trusted repair manual for specific guidance.
3

Hood Hinge Bolts (Estimated)

M8 x 1.25
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Estimated torque value based on industry standards. Consult the vehicle's manufacturer or a trusted repair manual for specific guidance.
4

Trunk Lid Hinge Bolts (Estimated)

M8 x 1.25
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Estimated torque value based on industry standards. Consult the vehicle's manufacturer or a trusted repair manual for specific guidance.
5

Door Hinge Bolts (Estimated)

M8 x 1.25
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Estimated torque value based on industry standards. Consult the vehicle's manufacturer or a trusted repair manual for specific guidance.
6

Fender Mounting Bolts (Estimated)

M10 x 1.5
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Estimated torque value based on industry standards. Consult the vehicle's manufacturer or a trusted repair manual for specific guidance.

Brakes

Torque specifications for Brakes

Brake Caliper

1

Brake Caliper Bolts

M10 x 1.25
Torque Specification
65 ft-lbs (88 N·m)
Important Notes
Ensure the caliper is properly aligned before torquing. Torque in a crisscross pattern.
2

Brake Caliper Mounting Bracket Bolts

M12 x 1.5
Torque Specification
72 ft-lbs (98 N·m)
Important Notes
Ensure the bracket is properly seated on the steering knuckle or axle.

Brake Rotor Drum

1

Brake Disc/Drum Retaining Bolts

M10 x 1.25
Torque Specification
65 ft-lbs (88 N·m)
Important Notes
Ensure the rotor or drum is properly seated on the hub before torquing.

Brake Hydraulics

1

Brake Hose Banjo Bolt

M10 x 1.0
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Ensure the sealing washers are properly seated. Torque evenly to avoid leaks.
2

Brake Master Cylinder Mounting Bolts

M8 x 1.25
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Ensure the master cylinder is properly aligned with the brake booster.

Brake Pedal Booster

1

Brake Pedal Pivot Bolt

M10 x 1.25
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Ensure the pedal operates smoothly after installation.
2

Brake Booster Mounting Bolts

M8 x 1.25
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Ensure the booster is properly aligned with the master cylinder.

Wheel Assembly

1

Wheel Lug Nuts

M12 x 1.5
Torque Specification
87 ft-lbs (118 N·m)
Important Notes
Torque in a star pattern to ensure even clamping force.

Drivetrain

Torque specifications for Drivetrain

Engine

1

Flywheel Bolts

M12 x 1.5
Torque Specification
65 ft-lbs (88 N·m)
Important Notes
Estimated value based on similar components. Actual value may vary.
2

Main Bearing Bolts

M14 x 1.5
Torque Specification
58 ft-lbs (79 N·m)
3

Connecting Rod Nuts

M10 x 1.5
Torque Specification
20 ft-lbs (27 N·m)
4

Crankshaft Pulley/Harmonic Balancer Bolt

M16 x 1.5
Torque Specification
126 ft-lbs (171 N·m)

Transmission

1

Transmission Mounting Bolts

M14 x 1.5
Torque Specification
72 ft-lbs (98 N·m)
2

Engine Block to Transmission Bellhousing Bolts

M12 x 1.5
Torque Specification
72 ft-lbs (98 N·m)
Important Notes
Estimated value based on similar components. Actual value may vary.
3

Transmission Crossmember Bolts

M14 x 1.5
Torque Specification
72 ft-lbs (98 N·m)
Important Notes
Estimated value based on similar components. Actual value may vary.

Drivetrain

1

Drive Axle/Half Shaft Bolts

M14 x 1.5
Torque Specification
72 ft-lbs (98 N·m)
2

CV Joint/Axle Nut

M18 x 1.5
Torque Specification
175 ft-lbs (237 N·m)
3

Propeller/Drive Shaft Bolts

M14 x 1.5
Torque Specification
72 ft-lbs (98 N·m)
4

Axle Shaft Retaining Bolts

M14 x 1.5
Torque Specification
72 ft-lbs (98 N·m)
Important Notes
Estimated value based on similar components. Actual value may vary.

Differential

1

Differential Cover Bolts

M10 x 1.5
Torque Specification
45 ft-lbs (61 N·m)
Important Notes
Estimated value based on similar components. Actual value may vary.
2

Differential Drain/Fill Plug

M12 x 1.5
Torque Specification
43 ft-lbs (58 N·m)

Electrical

Torque specifications for Electrical

Starter Motor

1

Starter Motor Mounting Bolts

M10 x 1.25
Torque Specification
36 ft-lbs (49 N·m)
Important Notes
Torque value is the midpoint of the specified range (32-40 ft-lbs).

Alternator

1

Alternator Mounting Bolts

M8 x 1.25
Torque Specification
18.5 ft-lbs (25 N·m)
Important Notes
Torque value is the midpoint of the specified range (17-20 ft-lbs).

Battery

1

Battery Terminal Nuts

M6 x 1.0
Torque Specification
4 ft-lbs (5.4 N·m)
Important Notes
Torque value is the midpoint of the specified range (3-5 ft-lbs).

Ignition System

1

Ignition Coil Bolt

M6 x 1.0
Torque Specification
0.65 ft-lbs (0.88 N·m)
Important Notes
Torque value is the midpoint of the specified range (69-86 inch-lbs). Converted to ft-lbs and N·m.

Grounding System

1

Ground Strap Bolts

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Torque value is the midpoint of the specified range (7-9 ft-lbs).

Fuse Box

1

Fuse Box Mounting Bolts

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Torque value is the midpoint of the specified range (7-9 ft-lbs).

Ecu

1

ECU Mounting Bolts

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Torque value is the midpoint of the specified range (7-9 ft-lbs).

Wiring Harness

1

Wiring Harness Clamp Bolts

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Torque value is the midpoint of the specified range (7-9 ft-lbs).

Emissions Sensors

Torque specifications for Emissions_sensors

Oxygen Sensors

1

Oxygen Sensor Bolts

M10 x 1.5
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
Estimated value, actual torque specification may vary depending on the manufacturer's recommendations.
2

Heated Oxygen Sensor (HO2S) Bolts

M10 x 1.5
Torque Specification
17.5 ft-lbs (24 N·m)
Important Notes
Estimated value, actual torque specification may vary depending on the manufacturer's recommendations.

EGR Valve and NOx Sensor

1

EGR Valve Bolts

M12 x 1.75
Torque Specification
15.5 ft-lbs (21 N·m)
2

NOx Sensor Bolts

M10 x 1.5
Torque Specification
17.5 ft-lbs (24 N·m)
Important Notes
Estimated value, actual torque specification may vary depending on the manufacturer's recommendations.

Exhaust Gas Temperature (EGT) Sensor

1

EGT Sensor Bolts

M10 x 1.5
Torque Specification
17.5 ft-lbs (24 N·m)
Important Notes
Estimated value, actual torque specification may vary depending on the manufacturer's recommendations.

Exhaust

Torque specifications for Exhaust

Exhaust Manifold Headers

1

Exhaust Manifold/Headers to Cylinder Head Bolts

M10 x 1.25
Torque Specification
29 ft-lbs (39 N·m)
Important Notes
Ensure bolts are tightened in a crisscross pattern to evenly distribute pressure.
2

Exhaust Manifold/Headers to Exhaust Pipe Bolts

M10 x 1.25
Torque Specification
29 ft-lbs (39 N·m)
Important Notes
Ensure gasket is properly seated before tightening.

Catalytic Converter

1

Catalytic Converter to Exhaust Pipe Bolts

M10 x 1.25
Torque Specification
29 ft-lbs (39 N·m)
Important Notes
Ensure gasket is properly seated before tightening.

Muffler

1

Muffler to Exhaust Pipe Bolts

M10 x 1.25
Torque Specification
29 ft-lbs (39 N·m)
Important Notes
Ensure gasket is properly seated before tightening.

Heat Shield

1

Exhaust Heat Shield Bolts

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Estimated value based on typical heat shield bolt sizes.

Exhaust Hanger

1

Exhaust Hanger Bolts

M8 x 1.25
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Estimated value based on typical exhaust hanger bolt sizes.

Oxygen Sensor

1

Oxygen Sensor (O2 Sensor)

M18 x 1.5
Torque Specification
35 ft-lbs (47 N·m)
Important Notes
Ensure sensor is properly aligned before tightening.

Exhaust Flange

1

Exhaust Flange Bolts

M10 x 1.25
Torque Specification
29 ft-lbs (39 N·m)
Important Notes
Ensure gasket is properly seated before tightening.

Fuel

Torque specifications for Fuel

Intake Manifold Subsystem

1

Throttle Body Bolts

M10 x 1.5
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Estimated value based on similar components.
2

Intake Manifold Bolts

M12 x 1.75
Torque Specification
15.5 ft-lbs (21 N·m)

Fuel Rail Subsystem

1

Fuel Rail Bolts

M10 x 1.5
Torque Specification
15.5 ft-lbs (21 N·m)
2

Fuel Injector Bolts

M8 x 1.25
Torque Specification
14.5 ft-lbs (20 N·m)
3

Fuel Injector O-Ring Bolts

M6 x 1.0
Torque Specification
6 ft-lbs (8 N·m)
Important Notes
Estimated value based on general industry standards.

Fuel Pump and Tank Subsystem

1

Fuel Pump Mounting Bolts

M12 x 1.75
Torque Specification
15.5 ft-lbs (21 N·m)
2

Fuel Tank Strap Bolts

M14 x 2.0
Torque Specification
28.5 ft-lbs (39 N·m)

Fuel Filler and Filter Subsystem

1

Fuel Filler Neck Bolts

M8 x 1.25
Torque Specification
8 ft-lbs (11 N·m)
2

Fuel Filter Bolt/Nut

M12 x 1.75
Torque Specification
20 ft-lbs (27 N·m)

Fuel Pressure Regulator Subsystem

1

Fuel Pressure Regulator Bolt

M10 x 1.5
Torque Specification
12.5 ft-lbs (17 N·m)
Important Notes
Estimated value based on general industry standards.

Hvac

Torque specifications for Hvac

Ac Compressor

1

A/C Compressor Mounting Bolts

M10 x 1.5
Torque Specification
35 ft-lbs (47 N·m)
Important Notes
Ensure bolts are tightened in a cross pattern to evenly distribute load.

Ac Lines

1

A/C Line Fittings

M8 x 1.25
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Use a torque wrench to avoid over-tightening, which can damage fittings.

Evaporator

1

Evaporator Core Housing Bolts

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Estimated value based on similar M6 bolts in HVAC systems.

Blower Motor

1

Blower Motor Mounting Bolts

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Estimated value based on similar M6 bolts in HVAC systems.

Heater Core

1

Heater Core Inlet/Outlet Fittings

M8 x 1.25
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Use a torque wrench to avoid over-tightening, which can damage fittings.

Control Panel

1

HVAC Control Panel Mounting Screws

M4 x 0.7
Torque Specification
0.9 ft-lbs (1.2 N·m)
Important Notes
Estimated value based on similar M4 screws in dashboard applications.

Condenser

1

Condenser Mounting Bolts

M8 x 1.25
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Ensure bolts are tightened in a cross pattern to evenly distribute load.

Suspension

Torque specifications for Suspension

Strut And Shock Absorber

1

Strut/Shock Absorber Mounting Bolts

M14 x 1.5
Torque Specification
41 ft-lbs (55 N·m)

Control Arm

1

Control Arm Bolts

M16 x 1.5
Torque Specification
65 ft-lbs (88 N·m)
2

Upper Control Arm Bushing Bolts

M12 x 1.25
Torque Specification
40 ft-lbs (54 N·m)
Important Notes
Estimated value based on general industry standards.
3

Lower Control Arm Bushing Bolts

M12 x 1.25
Torque Specification
40 ft-lbs (54 N·m)
Important Notes
Estimated value based on general industry standards.

Steering Knuckle

1

Steering Knuckle Bolts

M18 x 1.5
Torque Specification
70 ft-lbs (95 N·m)
Important Notes
Estimated value based on general industry standards.

Ball Joint And Tie Rod

1

Ball Joint Nut

M14 x 1.5
Torque Specification
32 ft-lbs (43 N·m)
2

Tie Rod End Nut

M12 x 1.25
Torque Specification
29 ft-lbs (39 N·m)

Sway Bar And Coil Spring

1

Sway Bar Link Nut

M12 x 1.25
Torque Specification
32 ft-lbs (43 N·m)
2

Coil Spring Mounting Bolts

M14 x 1.5
Torque Specification
30 ft-lbs (40 N·m)
Important Notes
Estimated value based on general industry standards.
3

Stabilizer Bar Mounting Bolts

M14 x 1.5
Torque Specification
30 ft-lbs (40 N·m)
Important Notes
Estimated value based on general industry standards.

Troubleshooting Guide

Common issues, diagnostic steps, and prevention guidelines

Common Issues

Bolt stretching, stripped threads, uneven torque patterns

Loose Components

Symptoms:
  • Rattling or vibration noises
  • Visible movement in components
  • Uneven panel gaps
Solutions:
  • Clean threads and mounting surfaces
  • Replace damaged fasteners
  • Apply proper torque in sequence
  • Use thread locker if specified

Stripped Fasteners

Symptoms:
  • Unable to achieve proper torque
  • Fastener spins freely
  • Visible thread damage
Solutions:
  • Use thread repair kit if appropriate
  • Install thread insert (HeliCoil)
  • Replace component if threaded hole is damaged
  • Upgrade to higher grade fastener if recommended

Overtightened Components

Symptoms:
  • Cracked or deformed parts
  • Broken fasteners
  • Compressed gaskets or seals
Solutions:
  • Replace damaged components
  • Use new fasteners
  • Follow proper torque sequence
  • Verify correct torque specifications

Diagnostic Steps

Visual inspection, torque verification, thread assessment

1

Visual Inspection

Inspect the affected area for any visible signs of damage or wear

  • Check for cracks or deformation
  • Look for signs of excessive wear
  • Verify proper fastener installation
2

Torque Verification

Verify the torque applied to the fasteners

  • Check the torque wrench calibration
  • Verify the torque specification
  • Compare the applied torque to the specification
3

Thread Assessment

Assess the condition of the threads

  • Check for signs of thread damage
  • Verify the thread type and size
  • Check for proper thread engagement

Prevention Guidelines

Best practices, maintenance tips, tool care

Best Practices

  • Always follow the recommended torque specification
  • Use the correct type and size of fasteners
  • Verify the torque wrench calibration regularly

Maintenance Tips

  • Regularly inspect the affected area for signs of wear or damage
  • Replace damaged or worn-out components promptly
  • Keep the work area clean and organized

Tool Care

  • Regularly clean and maintain the torque wrench
  • Store the torque wrench in a dry and secure location
  • Verify the torque wrench calibration before each use

Frequently Asked Questions

Find answers to common questions about torque specifications

Q1

What IS the recommended torque for lug nuts on a 2011-2018 Hyundai Veloster?

The recommended torque for lug nuts on a 2011-2018 Hyundai Veloster IS 81 lb-ft (110 Nm).

Q2

What IS the correct torque for spark plugs on a 2011-2018 Hyundai Veloster?

The correct torque for spark plugs on a 2011-2018 Hyundai Veloster IS 18 lb-ft (24 Nm).

Q3

What type of torque wrench should I use for tightening bolts on my Hyundai Veloster?

It IS recommended to use a click-type torque wrench to ensure accurate torque application. Refer to the manufacturer's instructions for proper usage.

Q4

IS it necessary to lubricate bolts before tightening them?

In general, it IS not necessary to lubricate bolts before tightening them, unless specified in the maintenance manual. Lubrication can reduce the accuracy of torque measurements.

Q5

What are the consequences of over-tightening or under-tightening bolts?

Over-tightening bolts can damage the threads, strip the bolt, or cause the bolt to snap. Under-tightening bolts can lead to loose connections, noise, and potential safety hazards.

Q6

Can I use a torque multiplier to increase the torque applied?

Yes, a torque multiplier can be used to increase the torque applied, but it IS important to follow the manufacturer's instructions carefully. Ensure the torque multiplier IS properly calibrated and compatible with your torque wrench.

Environmental Considerations

Temperature, humidity, and seasonal effects on torque specifications

Temperature Effects

Includes: High Heat, Cold Weather, Thermal Cycling

Temperature can significantly impact torque values and fastener behavior

Cold Weather

Effects:
  • Increased material brittleness
  • Higher torque required due to thread contraction
  • Reduced thread lubricant effectiveness
Recommendations:
  • Allow components to warm to room temperature when possible
  • Consider using winter-grade thread lubricants
  • Check torque values more frequently during winter months

Hot Weather

Effects:
  • Thermal expansion of components
  • Decreased friction in threads
  • Accelerated lubricant breakdown
Recommendations:
  • Check torque when components are at normal operating temperature
  • Use temperature-resistant thread lockers
  • Consider re-torquing after heat cycles

Humidity and Corrosion

Covers: Rust Prevention, Salt Exposure, Moisture Control

Moisture and corrosion can affect fastener integrity and torque values

High Humidity

Effects:
  • Accelerated corrosion formation
  • Reduced friction coefficient
  • Potential thread seizing
Prevention:
  • Use corrosion-resistant fasteners
  • Apply appropriate anti-seize compounds
  • Maintain proper protective coatings

Salt Exposure

Effects:
  • Rapid corrosion development
  • Thread damage
  • Seized fasteners
Prevention:
  • Regular underbody washing
  • Use of sacrificial anodes where appropriate
  • Application of protective coatings

Seasonal Maintenance

Spring, Summer, Fall, and Winter maintenance schedules

Spring

  • Inspect for winter damage
  • Clean and protect exposed fasteners
  • Check torque on critical components

Summer

  • Monitor heat-affected components
  • Check expansion-related loosening
  • Inspect cooling system mounts

Fall

  • Prepare for winter conditions
  • Apply corrosion protection
  • Verify all fasteners are properly torqued

Winter

  • More frequent inspection of critical fasteners
  • Check for salt damage
  • Monitor suspension component torque

Related Resources

Tools, service procedures, and technical bulletins

Recommended Tools

Digital Torque Wrench (10-100 Nm)

Essential for tightening fasteners to precise torque specifications, preventing damage and ensuring proper assembly. This range IS suitable for many applications on the veloster.

  • Digital display for accurate readings
  • Audible alarm when target torque IS reached
  • Multiple units (Nm, ft-lb, in-lb)
  • Reversible ratcheting mechanism
Learn more
Service Procedures
Technical Service Bulletins

Legal Disclaimer

Important information about using this content

Always refer to your vehicle's service manual and take appropriate safety precautions when performing any maintenance or repairs.

General Information
The information provided on this website is for general informational purposes only. While we strive to maintain accuracy in our content, all specifications, procedures, and technical information should be verified against your vehicle's official service manual or with the manufacturer directly.
Warranty & Liability

The content on this website is provided "as is" without any representations or warranties, express or implied. We make no representations or warranties regarding the accuracy, completeness, or availability of the information.

We shall not be liable for any direct, indirect, special, or consequential damages arising from the use of information on this website.

Technical Information
  • All specifications, including torque values, fluid capacities, and maintenance procedures, should be verified against your vehicle's factory service manual.
  • Vehicle specifications and procedures may vary by model year, trim level, and region.
  • Always follow the manufacturer's recommended procedures and safety precautions.
  • Working on vehicles can be dangerous. Always take proper safety precautions and use appropriate safety equipment.
  • If you're unsure about any procedure, consult a qualified professional mechanic.
Intellectual Property
All content, including text, images, and specifications, is protected by copyright and other intellectual property laws. Any unauthorized use or reproduction is prohibited.

About the Author

Expert automotive knowledge and experience

Alan Montanye - Automotive Technical Specialist
ASE

Alan Montanye

Automotive Technical Specialist

ASE Master Certified Technician with over a decade of hands-on experience in automotive repair and diagnostics.

Facebook Contact
15+ Years
Experience
500+ Guides
Guides
50+ Makes
Vehicles
1000+ Solutions
Solutions

Diagnostic

Specialized in advanced diagnostic techniques using modern scan tools and oscilloscopes.

Repair

Expert in both traditional mechanical repairs and modern vehicle systems.

Additional Expertise

Documentation

Created over 500 detailed repair guides and technical documents.

Training

Conducted technical training sessions and contributed to repair databases.

Certifications & Research

Certifications

  • ASE Master Technician Certification
  • Advanced Diagnostic Specialist
  • Hybrid/Electric Vehicle Systems
  • Performance Tuning Expert

Research & Community

Actively researches emerging technologies and contributes to automotive forums.

© 2025 Hyundai Specs. All rights reserved.

Privacy Policy Terms of Service