Hyundai Vehicle Models Veloster 2019-present Torque Specifications
Hyundai Vehicle Models Veloster 2019-present

Hyundai Vehicle Models Veloster 2019-present Torque Specifications

Complete Hyundai Vehicle Models Veloster 2019-present torque specifications guide. Includes factory-specified torque values, torque sequences, and technical specifications for all components including body, brakes, drivetrain, electrical, emissions sensors, fuel, exhaust, HVAC, and suspension. Essential information for proper assembly and maintenance.

Updated

Important Information

Safety guidelines and reference information for proper torque application

Quick Reference Guide
ft-lbs → Nm
× 1.356
ft-lbs → kg-m
× 0.138
Nm → ft-lbs
× 0.738
in-lbs → ft-lbs
× 0.083

Common Torque Patterns

Star Pattern

Used for wheels and other circular bolt patterns

Star Pattern torque pattern diagram showing proper bolt tightening sequence
Cross Pattern

Used for gaskets and cover plates

Cross Pattern torque pattern diagram showing proper bolt tightening sequence
Sequential Pattern

Used for head bolts and other critical components

Sequential Pattern torque pattern diagram showing proper bolt tightening sequence

Common Mistakes to Avoid

Over-tightening

Exceeding the specified torque value can stretch or break fasteners, damage threads, or crack components.

Prevention:

Always use a calibrated torque wrench and follow specifications exactly.

Incorrect Torque Sequence

Tightening bolts in the wrong order can cause uneven pressure distribution and potential leaks or damage.

Prevention:

Follow the manufacturer's specified torque sequence pattern.

Dirty Threads

Dirt, rust, or old thread locker can affect torque readings and proper fastener tension.

Prevention:

Clean and inspect all threads before assembly. Use new thread locker if specified.

Reusing TTY Bolts

Torque-to-yield bolts are designed to stretch and must not be reused.

Prevention:

Always replace TTY bolts with new ones. They are single-use only.

Dry vs. Lubricated

Not accounting for whether torque specs are for dry or lubricated fasteners can lead to incorrect tension.

Prevention:

Check if specs are for dry or lubricated threads. Use specified lubricant when required.

Recommended Tools

Torque Wrench (1/4" Drive)

Range: 2-25 ft-lbs
Small fasteners, delicate components

Torque Wrench (3/8" Drive)

Range: 10-100 ft-lbs
Most common automotive fasteners

Torque Wrench (1/2" Drive)

Range: 30-250 ft-lbs
Large fasteners, wheels

Angle Gauge

Torque-to-yield (TTY) bolts

Torque Wrench Care

  • Calibrate annually or after 5,000 clicks
  • Store at lowest setting
  • Keep clean and lubricated

Search Specifications

Search by component name, bolt size, or description

Torque Calculator

Convert between different torque units

1.6l Engine

Torque specifications for 1.6L Engine

Cylinder Head

1

Cylinder Head Bolts

M10 x 1.25
Torque Specification
1. 18 ft-lbs (24.4 N·m) 2. 90°
Important Notes
Follow the specified torque sequence to ensure proper sealing and prevent warping.
2

Valve Cover Bolts

M6 x 1.0
Torque Specification
4 ft-lbs (5.4 N·m)
Important Notes
Ensure the valve cover gasket is properly seated before tightening.

Crankshaft And Bearings

1

Main Bearing Bolts

M10 x 1.25
Torque Specification
1. 18 ft-lbs (24.4 N·m) 2. 90°
Important Notes
Follow the specified torque sequence to ensure proper crankshaft alignment.
2

Flywheel Bolts

M12 x 1.5
Torque Specification
94 ft-lbs (127.3 N·m)
Important Notes
Use thread locker on flywheel bolts to prevent loosening.

Timing System

1

Timing Belt/Chain Tensioner Bolt

M8 x 1.25
Torque Specification
18 ft-lbs (24.4 N·m)
Important Notes
Ensure proper tension on the timing belt/chain before tightening.
2

Camshaft Sprocket Bolt

M10 x 1.25
Torque Specification
63 ft-lbs (85.5 N·m)
Important Notes
Use a holding tool to prevent the camshaft from rotating while tightening.

Turbocharger System

1

Turbocharger Mounting Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (24.4 N·m)
Important Notes
Estimated value based on similar turbocharger systems.
2

Turbocharger Oil Feed Line Bolt

M8 x 1.25
Torque Specification
18 ft-lbs (24.4 N·m)
Important Notes
Estimated value based on similar turbocharger systems.

1.6l Turbo Engine

Torque specifications for 1.6L-TURBO Engine

Cylinder Head

1

Cylinder Head Bolts

M10 x 1.25
Torque Specification
1. 18 ft-lbs (24.4 N·m) 2. 90°
Important Notes
Follow the specified torque sequence to ensure proper sealing and prevent warping.
2

Valve Cover Bolts

M6 x 1.0
Torque Specification
4 ft-lbs (5.4 N·m)
Important Notes
Ensure the valve cover gasket is properly seated before tightening.

Crankshaft And Bearings

1

Main Bearing Bolts

M10 x 1.25
Torque Specification
1. 18 ft-lbs (24.4 N·m) 2. 90°
Important Notes
Follow the specified torque sequence to ensure proper crankshaft alignment.
2

Flywheel Bolts

M12 x 1.5
Torque Specification
94 ft-lbs (127.3 N·m)
Important Notes
Use thread locker on flywheel bolts to prevent loosening.

Timing System

1

Timing Belt/Chain Tensioner Bolt

M8 x 1.25
Torque Specification
18 ft-lbs (24.4 N·m)
Important Notes
Ensure proper tension on the timing belt/chain before tightening.
2

Camshaft Sprocket Bolt

M10 x 1.25
Torque Specification
63 ft-lbs (85.5 N·m)
Important Notes
Use a holding tool to prevent the camshaft from rotating while tightening.

Turbocharger System

1

Turbocharger Mounting Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (24.4 N·m)
Important Notes
Estimated value based on similar turbocharger systems.
2

Turbocharger Oil Feed Line Bolt

M8 x 1.25
Torque Specification
18 ft-lbs (24.4 N·m)
Important Notes
Estimated value based on similar turbocharger systems.

2.0l Engine

Torque specifications for 2.0L Engine

Cylinder Head

1

Cylinder Head Bolts

M10 x 1.25
Torque Specification
1. 18 ft-lbs (24.4 N·m) 2. 90°
Important Notes
Follow the manufacturer's torque sequence to avoid warping the cylinder head.
2

Valve Cover Bolts

M6 x 1.0
Torque Specification
4 ft-lbs (5.4 N·m)
Important Notes
Ensure the valve cover gasket is properly seated before tightening.

Crankshaft And Bearings

1

Main Bearing Bolts

M10 x 1.25
Torque Specification
18 ft-lbs (24.4 N·m)
Important Notes
Follow the manufacturer's torque sequence to ensure proper crankshaft alignment.
2

Crankshaft Pulley/Harmonic Balancer Bolt

M14 x 1.5
Torque Specification
130 ft-lbs (176.3 N·m)
Important Notes
Ensure the pulley is properly seated before tightening.

Timing System

1

Timing Belt/Chain Tensioner Bolt

M8 x 1.25
Torque Specification
18 ft-lbs (24.4 N·m)
Important Notes
Ensure the tensioner is properly aligned before tightening.
2

Camshaft Sprocket Bolt

M12 x 1.25
Torque Specification
63 ft-lbs (85.5 N·m)
Important Notes
Ensure the sprocket is properly aligned with the timing marks.

Intake And Exhaust

1

Intake Manifold Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (24.4 N·m)
Important Notes
Follow the manufacturer's torque sequence to avoid warping the manifold.
2

Exhaust Manifold/Headers Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (24.4 N·m)
Important Notes
Follow the manufacturer's torque sequence to avoid warping the manifold.

Oil System

1

Oil Pan Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (9.5 N·m)
Important Notes
Ensure the oil pan gasket is properly seated before tightening.
2

Oil Drain Plug Bolt

M12 x 1.5
Torque Specification
29 ft-lbs (39.3 N·m)
Important Notes
Replace the crush washer to ensure a proper seal.

Body

Torque specifications for Body

Suspension and Steering

1

Strut/Shock Absorber Mounting Bolts

M14 x 1.5
Torque Specification
40 ft-lbs (54.2 N·m)
2

Control Arm Bolts

M16 x 1.5
Torque Specification
74 ft-lbs (100.3 N·m)
3

Ball Joint Nut

M12 x 1.5
Torque Specification
40 ft-lbs (54.2 N·m)
4

Tie Rod End Nut

M10 x 1.5
Torque Specification
29 ft-lbs (39.3 N·m)
5

Sway Bar Link Nut

M12 x 1.5
Torque Specification
44 ft-lbs (59.7 N·m)
6

Steering Gear/Rack Bolts

M14 x 1.5
Torque Specification
74 ft-lbs (100.3 N·m)

Body and Trim

1

Hood Hinge Bolts

M10 x 1.5
Torque Specification
15 ft-lbs (20.3 N·m)
Important Notes
Estimated value based on general industry standards.
2

Trunk Lid Hinge Bolts

M10 x 1.5
Torque Specification
15 ft-lbs (20.3 N·m)
Important Notes
Estimated value based on general industry standards.
3

Door Hinge Bolts

M10 x 1.5
Torque Specification
15 ft-lbs (20.3 N·m)
Important Notes
Estimated value based on general industry standards.
4

Bumper Mounting Bolts

M12 x 1.5
Torque Specification
20 ft-lbs (27.1 N·m)
Important Notes
Estimated value based on general industry standards.
5

Fender Mounting Bolts

M10 x 1.5
Torque Specification
15 ft-lbs (20.3 N·m)
Important Notes
Estimated value based on general industry standards.

Brakes

Torque specifications for Brakes

Brake Caliper Assembly

1

Brake Caliper Bolts

M10 x 1.25
Torque Specification
25 ft-lbs (33.9 N·m)
Important Notes
Ensure the caliper is properly aligned before torquing.
2

Brake Caliper Mounting Bracket Bolts

M12 x 1.5
Torque Specification
60 ft-lbs (81.3 N·m)
Important Notes
Ensure the mounting bracket is securely attached to the chassis.

Brake Disc Drum Assembly

1

Brake Disc/Drum Retaining Bolts

M8 x 1.25
Torque Specification
32 ft-lbs (43.4 N·m)
Important Notes
Ensure the disc/drum is properly seated on the hub before torquing.

Wheel Assembly

1

Wheel Lug Nuts

M14 x 1.5
Torque Specification
80 ft-lbs (108.5 N·m)
Important Notes
Use a star pattern to tighten lug nuts for even distribution of torque.

Brake Hydraulic System

1

Brake Master Cylinder Mounting Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (24.4 N·m)
Important Notes
Ensure the master cylinder is properly aligned before torquing.
2

Brake Hose/Line Fittings

M10 x 1.0
Torque Specification
18 ft-lbs (24.4 N·m)
Important Notes
Ensure the fittings are properly seated and free of debris before torquing.

Brake Pedal Assembly

1

Brake Pedal Assembly Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (24.4 N·m)
Important Notes
Ensure the pedal assembly is properly aligned before torquing.

D7f Transmission

Torque specifications for D7f Transmission

Transmission Mounting

1

Transmission Mounting Bolts

M12 x 1.5
Torque Specification
37 ft-lbs (50.1 N·m)

Transmission Oil Pan

1

Transmission Oil Pan Bolts

M8 x 1.25
Torque Specification
6.9 ft-lbs (9.5 N·m)
Important Notes
Note: The torque value is converted from 84 inch-lbs to ft-lbs and Nm.

Transmission Fluid System

1

Transmission Drain and Fill Plugs

M14 x 1.5
Torque Specification
29 ft-lbs (39.3 N·m)
2

Transmission Fluid Drain/Fill Plug

M14 x 1.5
Torque Specification
29 ft-lbs (39.3 N·m)

Transmission Case and Bellhousing

1

Transmission Case Bolts

M14 x 1.5
Torque Specification
40 ft-lbs (54.2 N·m)
Important Notes
Note: The torque value is estimated based on industry standards for similar transmission designs.
2

Transmission Bellhousing Bolts

M12 x 1.5
Torque Specification
30 ft-lbs (40.7 N·m)
Important Notes
Note: The torque value is estimated based on industry standards for similar transmission designs.

Transmission Pan Gasket

1

Transmission Pan Gasket Bolts

M8 x 1.25
Torque Specification
10 ft-lbs (13.6 N·m)
Important Notes
Note: The torque value is estimated based on industry standards for similar transmission designs.

D8f Transmission

Torque specifications for D8f Transmission

Transmission Mounting

1

Transmission Mounting Bolts

M12 x 1.5
Torque Specification
37 ft-lbs (50.1 N·m)

Transmission Oil Pan

1

Transmission Oil Pan Bolts

M8 x 1.25
Torque Specification
6.2 ft-lbs (9.5 N·m)
Important Notes
Estimated bolt size, consult manufacturer's recommendations for accurate information.

Transmission Fluid System

1

Transmission Drain and Fill Plugs

M14 x 1.5
Torque Specification
29 ft-lbs (39.3 N·m)
2

Transmission Fluid Drain/Fill Plug

M14 x 1.5
Torque Specification
29 ft-lbs (39.3 N·m)

Transmission Case

1

Transmission Case Bolts

M10 x 1.5
Torque Specification
1. 40 ft-lbs (54.2 N·m) 2. 50 ft-lbs (67.8 N·m)
Important Notes
Estimated torque values, consult manufacturer's recommendations for accurate information.

Transmission Bellhousing

1

Transmission Bellhousing Bolts

M12 x 1.5
Torque Specification
1. 30 ft-lbs (40.7 N·m) 2. 40 ft-lbs (54.2 N·m)
Important Notes
Estimated torque values, consult manufacturer's recommendations for accurate information.

Transmission Cooler Lines

1

Transmission Cooler Line Fittings

M10 x 1.5
Torque Specification
1. 20 ft-lbs (27.1 N·m) 2. 30 ft-lbs (40.7 N·m)
Important Notes
Estimated torque values, consult manufacturer's recommendations for accurate information.

Transmission Solenoid Pack

1

Transmission Solenoid Pack Bolts

M8 x 1.25
Torque Specification
1. 10 ft-lbs (13.6 N·m) 2. 20 ft-lbs (27.1 N·m)
Important Notes
Estimated torque values, consult manufacturer's recommendations for accurate information.

Drivetrain

Torque specifications for Drivetrain

Engine and Transmission Mounting

1

Transmission Mounting Bolts

M12 x 1.5
Torque Specification
37 ft-lbs (50.1 N·m)
2

Engine Mounting Bolts

M14 x 1.5
Torque Specification
50 ft-lbs (67.8 N·m)
Important Notes
Estimated value, consult manufacturer's documentation for precise torque value.

Flywheel and Clutch

1

Flywheel Bolts

M10 x 1.25
Torque Specification
94 ft-lbs (127.3 N·m)

Transmission and Drive Axle

1

Transmission Oil Pan Bolts

M8 x 1.25
Torque Specification
84 ft-lbs (9.5 N·m)
Important Notes
Note: The specified torque value is in inch-lbs, converted to ft-lbs for consistency.
2

Drive Axle/Half Shaft Bolts

M12 x 1.5
Torque Specification
59 ft-lbs (79.9 N·m)
3

CV Joint/Axle Nut

M20 x 1.5
Torque Specification
145 ft-lbs (196.6 N·m)

Differential and Axle Shaft

1

Differential Cover Bolts

M10 x 1.25
Torque Specification
70 ft-lbs (94.9 N·m)
Important Notes
Estimated value, consult manufacturer's documentation for precise torque value.
2

Axle Shaft Retainer Bolts

M12 x 1.5
Torque Specification
40 ft-lbs (54.2 N·m)
Important Notes
Estimated value, consult manufacturer's documentation for precise torque value.

Engine Internals

1

Main Bearing Bolts

M14 x 1.5
Torque Specification
18 ft-lbs (24.4 N·m)
2

Connecting Rod Nuts

M10 x 1.25
Torque Specification
15 ft-lbs (20.3 N·m)

Electrical

Torque specifications for Electrical

Alternator And Starter Motor

1

Alternator Mounting Bolts

M12 x 1.5
Torque Specification
18 ft-lbs (24.4 N·m)
2

Starter Motor Mounting Bolts

M14 x 1.5
Torque Specification
29 ft-lbs (39.3 N·m)

Battery And Ignition System

1

Battery Terminal Nuts

M8 x 1.25
Torque Specification
7 ft-lbs (9.5 N·m)
2

Ignition Coil Bolt

M10 x 1.5
Torque Specification
7 ft-lbs (9.5 N·m)

Spark Plug Wire Boot And Fuel Pump Electrical Connector

1

Spark Plug Wire Boot Nuts

M6 x 1
Torque Specification
1. 10 ft-lbs (13.6 N·m) 2. 15 ft-lbs (20.3 N·m)
Important Notes
Estimated torque values based on general industry standards.
2

Fuel Pump Electrical Connector Bolts

M8 x 1.25
Torque Specification
1. 7 ft-lbs (9.5 N·m) 2. 10 ft-lbs (13.6 N·m)
Important Notes
Estimated torque values based on general industry standards.

Oxygen Sensor Electrical Connector And ECM Mounting

1

Oxygen Sensor Electrical Connector Bolts

M8 x 1.25
Torque Specification
1. 7 ft-lbs (9.5 N·m) 2. 10 ft-lbs (13.6 N·m)
Important Notes
Estimated torque values based on general industry standards.
2

Engine Control Module (ECM) Mounting Bolts

M12 x 1.5
Torque Specification
1. 10 ft-lbs (13.6 N·m) 2. 15 ft-lbs (20.3 N·m)
Important Notes
Estimated torque values based on general industry standards.

Emissions Sensors

Torque specifications for Emissions_sensors

Exhaust Manifold Headers

1

Exhaust Manifold/Headers Bolts

M10 x 1.25
Torque Specification
18 ft-lbs (24.4 N·m)
Important Notes
Ensure bolts are tightened in a crisscross pattern to evenly distribute pressure.
2

Exhaust Manifold/Headers to Cylinder Head Bolts

M10 x 1.25
Torque Specification
18 ft-lbs (24.4 N·m)
Important Notes
Ensure a proper seal to prevent exhaust leaks.

Exhaust Pipe Connections

1

Exhaust Pipe to Exhaust Manifold/Headers Bolts

M10 x 1.25
Torque Specification
18 ft-lbs (24.4 N·m)
Important Notes
Ensure proper alignment before tightening.
2

Downpipe to Catalytic Converter Bolts

M10 x 1.25
Torque Specification
18 ft-lbs (24.4 N·m)
Important Notes
Estimated value based on similar exhaust system components.

Catalytic Converter

1

Catalytic Converter to Exhaust Pipe Bolts

M10 x 1.25
Torque Specification
18 ft-lbs (24.4 N·m)
Important Notes
Ensure proper alignment before tightening.
2

Catalytic Converter Heat Shield Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (9.5 N·m)
Important Notes
Estimated value based on similar heat shield applications.

Egr System

1

EGR Valve Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (24.4 N·m)
Important Notes
Ensure proper alignment before tightening.

Oxygen Sensor

1

Oxygen Sensor (O2 Sensor) Mounting Nut

M18 x 1.5
Torque Specification
30 ft-lbs (40.7 N·m)
Important Notes
Ensure proper alignment and avoid overtightening to prevent sensor damage.

Exhaust

Torque specifications for Exhaust

Exhaust Manifold Headers

1

Exhaust Manifold/Headers to Cylinder Head Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (24.4 N·m)
Important Notes
Ensure bolts are tightened in a crisscross pattern to evenly distribute pressure.
2

Exhaust Pipe to Exhaust Manifold/Headers Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (24.4 N·m)
Important Notes
Ensure gasket is properly seated before tightening.

Catalytic Converter

1

Catalytic Converter to Exhaust Pipe Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (24.4 N·m)
Important Notes
Ensure gasket is properly seated before tightening.

Muffler

1

Muffler to Exhaust Pipe Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (24.4 N·m)
Important Notes
Ensure gasket is properly seated before tightening.

Heat Shield

1

Exhaust Heat Shield Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (9.5 N·m)
Important Notes
Estimated value based on typical heat shield bolt sizes. Ensure not to over-tighten, as this could damage the heat shield.

Exhaust Hanger

1

Exhaust Hanger Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (24.4 N·m)
Important Notes
Ensure hanger brackets are properly aligned before tightening.

Oxygen Sensor

1

Oxygen Sensor Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (24.4 N·m)
Important Notes
Ensure sensor is properly seated before tightening.

Exhaust Flange

1

Exhaust Flange Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (24.4 N·m)
Important Notes
Ensure gasket is properly seated before tightening. Tighten bolts in a crisscross pattern.

Fuel

Torque specifications for Fuel

Fuel Rail System

1

Fuel Rail Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (24.4 N·m)
Important Notes
Ensure bolts are tightened in a crisscross pattern to evenly distribute pressure.
2

Fuel Injector Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (9.5 N·m)
Important Notes
Ensure injector O-rings are properly seated before tightening.

Fuel Pump And Tank

1

Fuel Pump Mounting Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (9.5 N·m)
Important Notes
Ensure the fuel pump flange is properly seated before tightening.
2

Fuel Tank Strap Bolts

M8 x 1.25
Torque Specification
15 ft-lbs (20.3 N·m)
Important Notes
Ensure the fuel tank is properly supported before tightening.
3

Fuel Tank Sender Unit Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (9.5 N·m)
Important Notes
Ensure the sender unit gasket is properly seated before tightening.

Fuel Delivery Components

1

High-Pressure Fuel Pump Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (24.4 N·m)
Important Notes
Ensure the pump is properly aligned before tightening.
2

Fuel Pressure Regulator Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (9.5 N·m)
Important Notes
Ensure the regulator is properly seated before tightening.
3

Fuel Line Fittings

M8 x 1.25
Torque Specification
18 ft-lbs (24.4 N·m)
Important Notes
Ensure fittings are properly aligned and seated before tightening.

Fuel Filter And Filler

1

Fuel Filter Bolt/Nut

M10 x 1.5
Torque Specification
22 ft-lbs (29.8 N·m)
Important Notes
Ensure the filter is properly aligned before tightening.
2

Fuel Filler Neck Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (9.5 N·m)
Important Notes
Ensure the filler neck is properly aligned before tightening.

Hvac

Torque specifications for Hvac

Compressor Subsystem

1

A/C Compressor Mounting Bolts

M10 x 1.25
Torque Specification
18 ft-lbs (24.4 N·m)
Important Notes
Ensure bolts are tightened in a crisscross pattern to evenly distribute load.

Refrigerant Lines Subsystem

1

A/C Line Fittings

M10 x 1.25
Torque Specification
18 ft-lbs (24.4 N·m)
Important Notes
Ensure fittings are clean and free of debris before tightening.

Blower Motor Subsystem

1

HVAC Blower Motor Mounting Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (24.4 N·m)
Important Notes
Estimated value based on similar components. Ensure bolts are tightened evenly to prevent motor misalignment.

Evaporator Core Subsystem

1

HVAC Evaporator Core Mounting Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (24.4 N·m)
Important Notes
Estimated value based on similar components. Ensure bolts are tightened evenly to prevent leaks or misalignment.

Condenser Subsystem

1

HVAC Condenser Mounting Bolts

M10 x 1.25
Torque Specification
18 ft-lbs (24.4 N·m)
Important Notes
Estimated value based on similar components. Ensure bolts are tightened evenly to prevent vibrations or leaks.

Control Unit Subsystem

1

HVAC Control Unit Mounting Bolts

M6 x 1.0
Torque Specification
18 ft-lbs (24.4 N·m)
Important Notes
Estimated value based on similar components. Ensure bolts are tightened evenly to prevent electrical or mechanical issues.

Suspension

Torque specifications for Suspension

Strut and Shock Absorber Mounting

1

Strut/Shock Absorber Mounting Bolts

M12 x 1.5
Torque Specification
40 ft-lbs (54.2 N·m)
Important Notes
These bolts secure the strut/shock absorber to the vehicle's frame.

Control Arm Mounting

1

Control Arm Bolts

M14 x 1.5
Torque Specification
74 ft-lbs (100.3 N·m)
Important Notes
These bolts attach the control arms to the frame and suspension components.
2

Upper Control Arm Bushing Bolts

M10 x 1.25
Torque Specification
1. 30 ft-lbs (40.7 N·m) 2. 40 ft-lbs (54.2 N·m)
Important Notes
These bolts secure the upper control arm bushings to the control arm. Estimated torque values.
3

Lower Control Arm Bushing Bolts

M10 x 1.25
Torque Specification
1. 30 ft-lbs (40.7 N·m) 2. 40 ft-lbs (54.2 N·m)
Important Notes
These bolts secure the lower control arm bushings to the control arm. Estimated torque values.

Ball Joint and Tie Rod End Mounting

1

Ball Joint Nut

M12 x 1.5
Torque Specification
40 ft-lbs (54.2 N·m)
Important Notes
This nut secures the ball joint to the control arm.
2

Tie Rod End Nut

M10 x 1.25
Torque Specification
29 ft-lbs (39.3 N·m)
Important Notes
This nut attaches the tie rod end to the steering rack or control arm.

Sway Bar and Stabilizer Bar Mounting

1

Sway Bar Link Nut

M12 x 1.5
Torque Specification
44 ft-lbs (59.7 N·m)
Important Notes
This nut secures the sway bar link to the sway bar and control arm.
2

Stabilizer Bar Mounting Bolts

M12 x 1.5
Torque Specification
1. 40 ft-lbs (54.2 N·m) 2. 50 ft-lbs (67.8 N·m)
Important Notes
These bolts attach the stabilizer bar to the frame or suspension components. Estimated torque values.

Steering Gear and Coil Spring Mounting

1

Steering Gear/Rack Bolts

M14 x 1.5
Torque Specification
74 ft-lbs (100.3 N·m)
Important Notes
These bolts attach the steering gear or rack to the frame.
2

Coil Spring Mounting Bolts

M12 x 1.5
Torque Specification
1. 40 ft-lbs (54.2 N·m) 2. 50 ft-lbs (67.8 N·m)
Important Notes
These bolts secure the coil spring to the strut or shock absorber. Estimated torque values.

Troubleshooting Guide

Common issues, diagnostic steps, and prevention guidelines

Common Issues

Bolt stretching, stripped threads, uneven torque patterns

Loose Components

Symptoms:
  • Rattling or vibration noises
  • Visible movement in components
  • Uneven panel gaps
Solutions:
  • Clean threads and mounting surfaces
  • Replace damaged fasteners
  • Apply proper torque in sequence
  • Use thread locker if specified

Stripped Fasteners

Symptoms:
  • Unable to achieve proper torque
  • Fastener spins freely
  • Visible thread damage
Solutions:
  • Use thread repair kit if appropriate
  • Install thread insert (HeliCoil)
  • Replace component if threaded hole is damaged
  • Upgrade to higher grade fastener if recommended

Overtightened Components

Symptoms:
  • Cracked or deformed parts
  • Broken fasteners
  • Compressed gaskets or seals
Solutions:
  • Replace damaged components
  • Use new fasteners
  • Follow proper torque sequence
  • Verify correct torque specifications

Diagnostic Steps

Visual inspection, torque verification, thread assessment

1

Visual Inspection

Inspect the affected area for any visible signs of damage or wear

  • Check for cracks or deformation
  • Look for signs of excessive wear
  • Verify proper fastener installation
2

Torque Verification

Verify the torque applied to the fasteners

  • Check the torque wrench calibration
  • Verify the torque specification
  • Compare the applied torque to the specification
3

Thread Assessment

Assess the condition of the threads

  • Check for signs of thread damage
  • Verify the thread type and size
  • Check for proper thread engagement

Prevention Guidelines

Best practices, maintenance tips, tool care

Best Practices

  • Always follow the recommended torque specification
  • Use the correct type and size of fasteners
  • Verify the torque wrench calibration regularly

Maintenance Tips

  • Regularly inspect the affected area for signs of wear or damage
  • Replace damaged or worn-out components promptly
  • Keep the work area clean and organized

Tool Care

  • Regularly clean and maintain the torque wrench
  • Store the torque wrench in a dry and secure location
  • Verify the torque wrench calibration before each use

Frequently Asked Questions

Find answers to common questions about torque specifications

Q1

What are the general torque guidelines for the 2019-Present Hyundai Veloster?

Always consult your vehicle's service manual for specific torque specifications. However, as a general rule, bolts and nuts should be tightened to the following approximate values: M6 bolts: 10-14 Nm (7-10 ft-lbs); M8 bolts: 20-28 Nm (15-21 ft-lbs); M10 bolts: 40-50 Nm (30-37 ft-lbs); M12 bolts: 60-75 Nm (44-55 ft-lbs).

Q2

What IS the proper tightening sequence for the cylinder head bolts on a 2019-Present Hyundai Veloster?

Refer to the manufacturer's service manual for the specific tightening sequence and torque specifications for your vehicle. Improper tightening can damage the cylinder head or bolts.

Q3

What are some common torque mistakes to avoid when working on a 2019-Present Hyundai Veloster?

Some common torque mistakes include using the wrong size socket or wrench, over-tightening bolts or nuts, and not following the proper tightening sequence. Always use a properly calibrated torque wrench and refer to the service manual for specific torque values.

Q4

What should I do if I accidentally over-tighten a bolt or nut on my 2019-Present Hyundai Veloster?

If you accidentally over-tighten a bolt or nut, do not attempt to loosen it by force. This could damage the bolt, nut, or surrounding components. Instead, consult a qualified mechanic for assistance.

Q5

Where can I find the torque specifications for my 2019-Present Hyundai Veloster?

The torque specifications for your vehicle can be found in the service manual or on a decal located in the engine compartment or on the inside of the driver's door jamb.

Q6

What IS the recommended torque for the lug nuts on a 2019-Present Hyundai Veloster?

The recommended torque for the lug nuts on a 2019-Present Hyundai Veloster IS 100 Nm (74 ft-lbs). Always refer to the service manual for the specific torque specifications for your vehicle and use a properly calibrated torque wrench when tightening lug nuts.

Environmental Considerations

Temperature, humidity, and seasonal effects on torque specifications

Temperature Effects

Includes: High Heat, Cold Weather, Thermal Cycling

Temperature can significantly impact torque values and fastener behavior

Cold Weather

Effects:
  • Increased material brittleness
  • Higher torque required due to thread contraction
  • Reduced thread lubricant effectiveness
Recommendations:
  • Allow components to warm to room temperature when possible
  • Consider using winter-grade thread lubricants
  • Check torque values more frequently during winter months

Hot Weather

Effects:
  • Thermal expansion of components
  • Decreased friction in threads
  • Accelerated lubricant breakdown
Recommendations:
  • Check torque when components are at normal operating temperature
  • Use temperature-resistant thread lockers
  • Consider re-torquing after heat cycles

Humidity and Corrosion

Covers: Rust Prevention, Salt Exposure, Moisture Control

Moisture and corrosion can affect fastener integrity and torque values

High Humidity

Effects:
  • Accelerated corrosion formation
  • Reduced friction coefficient
  • Potential thread seizing
Prevention:
  • Use corrosion-resistant fasteners
  • Apply appropriate anti-seize compounds
  • Maintain proper protective coatings

Salt Exposure

Effects:
  • Rapid corrosion development
  • Thread damage
  • Seized fasteners
Prevention:
  • Regular underbody washing
  • Use of sacrificial anodes where appropriate
  • Application of protective coatings

Seasonal Maintenance

Spring, Summer, Fall, and Winter maintenance schedules

Spring

  • Inspect for winter damage
  • Clean and protect exposed fasteners
  • Check torque on critical components

Summer

  • Monitor heat-affected components
  • Check expansion-related loosening
  • Inspect cooling system mounts

Fall

  • Prepare for winter conditions
  • Apply corrosion protection
  • Verify all fasteners are properly torqued

Winter

  • More frequent inspection of critical fasteners
  • Check for salt damage
  • Monitor suspension component torque

Related Resources

Tools, service procedures, and technical bulletins

Recommended Tools

Digital Torque Wrench (10-100 Nm)

Essential for tightening fasteners to precise torque specifications, preventing damage and ensuring proper assembly. This range IS suitable for many applications on the veloster.

  • Digital display for accurate readings
  • Audible alarm when target torque IS reached
  • Multiple units (Nm, ft-lb, in-lb)
  • Reversible ratcheting mechanism
Learn more
Service Procedures

Engine Crankshaft Pulley Bolt Replacement

Procedure for replacing the crankshaft pulley bolt on 2019-Present Hyundai Veloster.

  • Remove the serpentine belt.
  • Use a 22 mm socket to loosen the crankshaft pulley bolt.
  • Remove the crankshaft pulley.
  • Apply Loctite 243 threadlocker to the new crankshaft pulley bolt.
  • Tighten the new crankshaft pulley bolt to 100 Nm (74 lb-ft).
  • Reinstall the crankshaft pulley and serpentine belt.
View full procedure

Front Brake Pad Replacement

Procedure for replacing the front brake pads on 2019-Present Hyundai Veloster.

  • Remove the front wheels.
  • Use a 14 mm socket to remove the brake caliper mounting bolts.
  • Remove the brake caliper and hang it from the suspension with a wire or bungee cord.
  • Remove the old brake pads.
  • Install the new brake pads.
  • Install the brake caliper and tighten the mounting bolts to 118 Nm (87 lb-ft).
  • Reinstall the front wheels.
View full procedure
Technical Service Bulletins

Technical Service Bulletin: Engine Oil Consumption

2020-03-05

Bulletin addressing excessive engine oil consumption on 2019-2020 Hyundai Veloster with 1.6L Turbocharged GDI Engine.

2019-2020 veloster

Resolution: Replace piston rings and oil pump with updated components.

Legal Disclaimer

Important information about using this content

Always refer to your vehicle's service manual and take appropriate safety precautions when performing any maintenance or repairs.

General Information
The information provided on this website is for general informational purposes only. While we strive to maintain accuracy in our content, all specifications, procedures, and technical information should be verified against your vehicle's official service manual or with the manufacturer directly.
Warranty & Liability

The content on this website is provided "as is" without any representations or warranties, express or implied. We make no representations or warranties regarding the accuracy, completeness, or availability of the information.

We shall not be liable for any direct, indirect, special, or consequential damages arising from the use of information on this website.

Technical Information
  • All specifications, including torque values, fluid capacities, and maintenance procedures, should be verified against your vehicle's factory service manual.
  • Vehicle specifications and procedures may vary by model year, trim level, and region.
  • Always follow the manufacturer's recommended procedures and safety precautions.
  • Working on vehicles can be dangerous. Always take proper safety precautions and use appropriate safety equipment.
  • If you're unsure about any procedure, consult a qualified professional mechanic.
Intellectual Property
All content, including text, images, and specifications, is protected by copyright and other intellectual property laws. Any unauthorized use or reproduction is prohibited.

About the Author

Expert automotive knowledge and experience

Alan Montanye - Automotive Technical Specialist
ASE

Alan Montanye

Automotive Technical Specialist

ASE Master Certified Technician with over a decade of hands-on experience in automotive repair and diagnostics.

Facebook Contact
15+ Years
Experience
500+ Guides
Guides
50+ Makes
Vehicles
1000+ Solutions
Solutions

Diagnostic

Specialized in advanced diagnostic techniques using modern scan tools and oscilloscopes.

Repair

Expert in both traditional mechanical repairs and modern vehicle systems.

Additional Expertise

Documentation

Created over 500 detailed repair guides and technical documents.

Training

Conducted technical training sessions and contributed to repair databases.

Certifications & Research

Certifications

  • ASE Master Technician Certification
  • Advanced Diagnostic Specialist
  • Hybrid/Electric Vehicle Systems
  • Performance Tuning Expert

Research & Community

Actively researches emerging technologies and contributes to automotive forums.

© 2025 Hyundai Specs. All rights reserved.

Privacy Policy Terms of Service